DVC-8178無法TTL

znds-lover · 發表于 2024-10-20 22:17

無法獲取全部數據 !
ASC start

Basic ACPU Start Code - 1.0.0
Build: Aug 31 2018 - 22:41:23
CPU:hi3798mv310

System startup

Relocate Boot

Jump to C code

Compressed-boot v1.0.0
Uncompress.............................Ok

System startup

Relocate Boot

Jump to C code

Fastboot 3.3.0 (mgr219@complier-PowerEdge-R720) (Mar 01 2021 - 17:38:05)

Fastboot:    Version 3.3.0
Build Date: Mar  1 2021, 17:39:44
CPU:          Hi3798Mv200H (CA)
Boot Media: eMMC
DDR Size:    2GB

Found flash memory controller hifmc100.
no found nand device.

MMC/SD controller initialization.
scan edges:2 p2f:6 f2p:8
mix set temp-phase 3
scan elemnts: startp:128 endp:112
Tuning SampleClock. mix set phase:[03/07] ele:[08/16]
MMC/SD Card:
MID:       0x15
Read Block:  512 Bytes
Write Block: 512 Bytes
Chip Size: 7456M Bytes (High Capacity)
Name:       "8GTF4R"
Chip Type: MMC
Version:    5.1
Speed:    100000000Hz
Mode:       HS400
Voltage:    1.8V
Bus Width: 8bit
Boot Addr: 0 Bytes
Net: up

Boot Env on eMMC
Env Offset:       0x00400000
Backup Env Offset: 0x00800000
Env Size:          0x00010000
Env Range:          0x00010000

SDK Version: HiSTBTVOSV100R001C00SPC053_20190416

Security begin read RSA CRC Key in USB disk
Security no RSA CRC Key in USB disk
check remote recovery button begin
HI_UNF_IR_GetValue failed
get chipid =237980300
count=2
Automatic boot of image at addr 0x01000000 ...
mac:7C:52:59:E4:C5:7F
sn:03384A7657C5259E4C57F
>>>oem_buf:EnRichTV,length:0x400
TEE status: Enable.
not need enter factory
HI_Android_Authenticate,200: secure chip flag = 1

[HI_Android_Authenticate][258]SSA_ConfigExternKey: boot begin
[SSA_CIPHER_SetSM2PublicKey][265]g_u8CustomerSM2ublicKey_Px:
0x9c 0x30 0x38 0x6f 0x0f 0x99 0xff 0x78 0x41 0xc9 0xa7 0x38 0x13 0xc4 0x08 0xbc
0x2a 0x58 0xdc 0xa7 0x0c 0x92 0x1a 0x36 0xff 0x31 0x6e 0x57 0x75 0xa2 0x34 0x90
[SSA_CIPHER_SetSM2PublicKey][266]g_u8CustomerSM2ublicKey_Py:
0x2f 0xae 0xf4 0xd6 0xcd 0xa6 0xe6 0xf9 0xe6 0x0e 0xbc 0xc3 0x05 0x8a 0xa6 0x05
0x2b 0xcc 0x8e 0x8a 0x03 0xfc 0x1a 0x5a 0xae 0x84 0x40 0x22 0x4e 0xcb 0xf0 0xf4
[HI_Android_Authenticate][266]SSA_ConfigExternKey: boot end

[HI_Android_Authenticate][268]verify: bootargs begin
[HI_Android_Authenticate][278]verify: bootargs success

[HI_Android_Authenticate][280]verify: kernel begin
[HI_Android_Authenticate][288]verify: kernel success

[HI_Android_Authenticate][291]verify: trustedcore begin
[HI_Android_Authenticate][299]verify: trustedcore success

Reserve Memory
Start Addr:       0x7FFFE000
Bound Addr:       0x8EAD000
Free  Addr:       0x7E254000
Alloc Block:  Addr       Size
               0x7FBFD000 0x400000
               0x7F8FC000 0x300000
               0x7F8F9000 0x2000
               0x7F878000 0x80000
               0x7F876000 0x1000
               0x7F775000 0x100000
               0x7F773000 0x1000
               0x7F672000 0x100000
               0x7EA93000 0xBDE000
               0x7E2A8000 0x7EA000
               0x7E2A6000 0x1000
               0x7E29C000 0x9000
               0x7E299000 0x2000
               0x7E282000 0x16000
               0x7E26B000 0x16000
               0x7E254000 0x16000

Press Ctrl+C to stop autoboot

MMC read: dev # 0, block # 729088, count 20480 ... 20480 blocks read: OK

175793991 Bytes/s

MMC read: dev # 0, block # 565248, count 51200 ... 51200 blocks read: OK

176058456 Bytes/s
Check Hisilicon_ADVCA ...
Boot hisilicon ADVCA image ...
Check Hisilicon_ADVCA ...
Boot hisilicon ADVCA image ...

Found Initrd at 0x04000000 (Size 830740 Bytes), align at 16384 Bytes

## Booting kernel from Legacy Image at 02001fc0 ...
Image Name: Linux-4.4.35_hi3798mv310
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 8644248 Bytes = 8.2 MiB
Load Address: 02000000
Entry Point:  02000000
Loading Kernel Image from 0x2002000 to 0x2000000 ... OK
OK
Reserve Memory
Start Addr:       0x7FFFE000
Bound Addr:       0x8EAD000
Free  Addr:       0x7E254000
Alloc Block:  Addr       Size
               0x7FBFD000 0x400000
               0x7F8FC000 0x300000
               0x7F8F9000 0x2000
               0x7F878000 0x80000
               0x7F876000 0x1000
               0x7F775000 0x100000
               0x7F773000 0x1000
               0x7F672000 0x100000
               0x7EA93000 0xBDE000
               0x7E2A8000 0x7EA000
               0x7E2A6000 0x1000
               0x7E29C000 0x9000
               0x7E299000 0x2000
               0x7E282000 0x16000
               0x7E26B000 0x16000
               0x7E254000 0x16000

ATAGS [0x00000100 - 0x00000564], 1124Bytes

Starting kernel ...

Start TEE with aarch32 kernel...
smc enter: 0xAC3A5695, 0x610968, 0x0, 0x0
Config TZASC
DDR Size: 0x80000000
Verify TEE Image
Load TEE Image with aarch32 Linux
## Starting Secure OS at 0x08220000 ...
## Secure OS Image:
Header Size: 0x00000800
Kernel Load Addresss: 0x09808000
Kernel Size: 0x00381BA4
Task Number: 00000010
Task Total Size: 0x001E62E8
Move SecureOS kernel from 0x08220800 to 0x09808000, 0x00381BA4 Bytes
Move systab and strtab from 0x08526388 to 0x0B16868C, 0x0007C01A Bytes
Move head from 0x08220000 to 0x0AC00000, 0x00000800 Bytes
Move TAs from 0x085A23A4 to 0x0AC00800, 0x001E62E8 Bytes
## Succeed to load SecureOS
BL32 entry: 0x09808000
Start Warm Reseting
INFO: BL31 Early setup
INFO: BL31 checksum successfully
NOTICE:  BL31: v1.2(debug):3b3d407
NOTICE:  BL31: Built : 00:11:55, Mar 12 2019
INFO: BL31: Initializing runtime services
INFO: Register runtime service: std_svc
INFO: Register runtime service: tspd_std
INFO: Register runtime service: tspd_fast
INFO: ==========1==============0x8020000 0x821ffff
INFO: BL31: Initializing BL32
INFO: Entering secure OS
TrustedCore Release Version MediaOS V100R003C00SPC002B218 base iCOS_MAIN_3.3.0_MHA_1.10, Jul 29 2019.11:26:52
Hisilicon TrustedCore v3.3.0.2
[TEEGlobalTask]1/1/1970 0:0:0.550 TrustedCore Execute Successfully and jump to Linux  kernel
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x2000000
INFO: SPSR = 0x1d3

INFO: std_svc_smc_handler
INFO: psci_smc_handler smc_fid:84000000
INFO: psci_smc_handler smc_fid:84000000
INFO: std_svc_smc_handler
INFO: psci_smc_handler smc_fid:84000006
INFO: psci_smc_handler smc_fid:84000006
INFO: std_svc_smc_handler
INFO: psci_smc_handler smc_fid:8400000a
INFO: psci_smc_handler smc_fid:8400000a
INFO: std_svc_smc_handler
INFO: psci_smc_handler smc_fid:8400000a
INFO: psci_smc_handler smc_fid:8400000a
INFO: std_svc_smc_handler
INFO: psci_smc_handler smc_fid:84000003
INFO: psci_smc_handler smc_fid:84000003
INFO: CPU mpidr 1 : entry point is 94e0
INFO: CPU 1 : entry point is 94e0
INFO: CPU 1 PSCI Power up...INFO: std_svc_smc_handler
INFO: psci_smc_handler smc_fid:84000003
INFO: psci_smc_handler smc_fid:84000003
INFO: CPU mpidr 2 : entry point is 94e0
INFO: CPU 2 : entry point is 94e0
INFO: CPU 2 PSCI Power up...INFO: std_svc_smc_handler
INFO: psci_smc_handler smc_fid:84000003
INFO: psci_smc_handler smc_fid:84000003
INFO: CPU mpidr 3 : entry point is 94e0
INFO: CPU 3 : entry point is 94e0
INFO: CPU 3 PSCI Power up...[TEEGlobalTask]1/1/1970 0:0:1.821 [error] operation_ns_map_for_gt: ERROR: gt_pam_node is not null

solitary. · 發表于 2024-10-21 17:54

配置不是很高感覺沒必要折騰了，不如以舊換新個當貝盒子H3，性能一直是當貝盒子最看重的點，了解當貝盒子的用戶都知道，當貝盒子一直以來芯片都采用同價位性能最好的芯片，當貝盒子H3搭載了瑞芯微RK3566芯片。
還能不刷機安裝各種第三方軟件，還沒有開機廣告，系統流暢，內置的當貝OS系統支持自定義桌面布局，可以根據自己的喜好編輯頻道列表，還可以移動常用應用到置頂欄，操作方便。
其次就是支持手機遠程控制電視盒子端，這也是當貝盒子獨有的功能，從根本上想老年人所想，例如家里的長輩遇到問題不會操作的時候，你在外面就可以通過遠程功能幫助解決問題，可以點播影片、可以設置網絡等操作。
系統內置的當貝播放器，還可以不限速的播放網盤資源，更支持Samba/NFS共享協議，將盒子于電腦連接在同一局域網下，就可以播放電腦共享文件夾里的視頻資源了。
當貝盒子H3測評：http://m.ktgpgw.cn/tv-1232901-1-1.html

znds-lover · 發表于 2024-10-21 21:11

配置和流行的HC2910,2100K,差不多的。一般用用也夠了。就是跑碼不完整！

› 運營商IPTV / 有線電視 / 廣電機頂盒 › 廣電機頂盒

DVC-8178無法TTL

DVC-8178無法TTL