putty跑碼完成不能輸入命令，機頂盒然后管腳

ZHL680 · 發表于 2024-6-21 11:07

本帖最后由智能小檸檬于 2024-6-21 16:53 編輯

GXLX:BL1:9ac50e:4a8da0;FEAT:ADFD318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 152648

BL2 Built : 17:15:25, Jun 21 2020.
gxl g85d6ad1 - longyong.chen@droid02-sz

Board ID = 4, adc=303
set vcck to 1120 mv
set vddee to 1000 mv
CPU clk: 1200MHz
DDR3LPower:
DDR3 chl: Rank0+1 @ 912MHz - FAIL
DDR3 chl: Rank0 @ 912MHz
bist_test rank: 0 17 00 2f 2a 12 43 16 00 2d 2e 15 48 19 04 2f 2d 14 47 19 03 2f 2e 13 4a 693 - PASS

Rank0: 1024MB(auto)-2T-13
ssc: ppm1000
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x013c0000, size: 0x00007600
Load bl301 from eMMC, src: 0x00018200, des: 0x01380000, size: 0x00002800
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019600
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x00081a00
NOTICE:  BL3-1: v1.0(debug):361f8a7
NOTICE:  BL3-1: Built : 16:43:26, Dec 19 2018
NOTICE:  BL31: GXL normal boot!
NOTICE:  BL31: BL33 decompress pass
[Image: gxl_v1.1.3103-9234004 2018-12-27 10:43:23 yao.zhang@droid07]
efuse init ops = c1
efuse init hdcp = c, cf9=7
x2_hp_e = 0
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: 0 0 3 c c 0 31 b3 58 a0 0 c1 not ES chip
[0.690889 Inits done]
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9

U-Boot 2015.01-ge0353cd-dirty (Oct 30 2023 - 22:01:56)

DRAM:  1 GiB
gxlx_p265_1g

[BL31]: tee size: 0

osd_size 720p
switch to partitions #0, OK
mmc1(part 0) is current device
bootmode:NORM
gxlx_p265_1g

IH_COMP_LZOOK
uboot time: 1797876 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] CPU: ARMv71 Processor [410fd034] revision 4
[ 0.000000@0] no prop version_code
[ 0.000000@0] bootconsole [earlycon0] enabled
get_dvfs_info 0004
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
[ ?[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
WARNING: Unimplemented Sip Call: 0x82000036
root@p200_2G:/ # [ 13.593521@3] monitor: received netlink message:anstvbw new ok
[ 13.593717@3] monitor:reply
GXLX:BL1:9ac50e:4a8da0;FEAT:ADFD318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 124679

BL2 Built : 17:15:25, Jun 21 2020.
gxl g85d6ad1 - longyong.chen@droid02-sz

Board ID = 4, adc=303
set vcck to 1120 mv
set vddee to 1000 mv
CPU clk: 1200MHz
DDR3LPower:
DDR3 chl: Rank0+1 @ 912MHz - FAIL
DDR3 chl: Rank0 @ 912MHz
bist_test rank: 0 17 00 2f 2a 12 43 16 00 2d 2f 16 48 19 04 2f 2d 14 47 19 03 2f 2e 13 49 693 - PASS

Rank0: 1024MB(auto)-2T-13
ssc: ppm1000
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x013c0000, size: 0x00007600
Load bl301 from eMMC, src: 0x00018200, des: 0x01380000, size: 0x00002800
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019600
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x00081a00
NOTICE:  BL3-1: v1.0(debug):361f8a7
NOTICE:  BL3-1: Built : 16:43:26, Dec 19 2018
NOTICE:  BL31: GXL normal boot!
NOTICE:  BL31: BL33 decompress pass
[Image: gxl_v1.1.3103-9234004 2018-12-27 10:43:23 yao.zhang@droid07]
efuse init ops = c1
efuse init hdcp = c, cf9=7
x2_hp_e = 0
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: 0 0 3 c c 0 31 b3 58 a0 0 c1 not ES chip
[0.662670 Inits done]
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9

U-Boot 2015.01-ge0353cd-dirty (Oct 30 2023 - 22:01:56)

DRAM:  1 GiB
gxlx_p265_1g

[BL31]: tee size: 0

osd_size 720p
switch to partitions #0, OK
mmc1(part 0) is current device
bootmode:NORM
gxlx_p265_1g

IH_COMP_LZOOK
uboot time: 1774305 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] CPU: ARMv71 Processor [410fd034] revision 4
[ 0.000000@0] no prop version_code
[ 0.000000@0] bootconsole [earlycon0] enabled
get_dvfs_info 0004
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
[ 1[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
WARNING: Unimplemented Sip Call: 0x82000036
root@p200_2G:/ # [ 13.619577@2] monitor: received netlink message:anstvbw new ok
[ 13.619765@2] monitor:reply
************
root@p200_2G:/ #代碼跑到此時不能輸入命令，等待幾秒出現：[ 13.619577@2] monitor: received netlink message:anstvbw new ok[ 13.619765@2] monitor:reply，然后機頂盒關機，是不是被鎖了

電視問答 · 發表于 2024-6-21 16:53

有截圖嗎

ZHL680 · 發表于 2024-6-22 10:30

電視問答發表于 2024-6-21 16:53
有截圖嗎

代碼就是全部截圖

yzk08 · 發表于 2024-9-12 15:16

同樣問題，求助

yzk08 · 發表于 2024-9-12 15:20

我的代碼如下：

yzk08 · 發表于 2024-9-12 15:25

CEC cfg:0x0000 hdmi 5v enter hdmi 5v leave vcc_5v enter vcc 5v leave set vddee to 0x0352mv set vddee to 0x0352mv 08915d0000000000 exit_reason: powerkey wakeup set vddee to 0x042emv set vddee to 0x042emv set vddee to 0x044cmv set vddee to 0x044cmv vcc_5v enter vcc 5v leave hdmi 5v enter hdmi 5v leave [ 456.771064@0] SysRq : Emergency Remount R/O [ 456.974163@0] reboot: Restarting system(init) with command '' INFO: PSCI Affinity Map: INFO: AffInst: Level 0, MPID 0x0, State ON INFO: AffInst: Level 0, MPID 0x1, State ON INFO: AffInst: Level 0, MPID 0x2, State ON INFO: AffInst: Level 0, MPID 0x3, State ON bl31 reboot reason: 0x1 bl31 reboot reason: 0x1 ERROR: gxbb System Reset: SCP error 1. GXL:BL1:9ac50e:bb16dc;FEAT:ADFD318C:0;POC:3;RCY:0;EMMC:800;NAND:0;READ:0;0.0;CHK:0; TE: 23984 BL2 Built : 17:15:25, Jun 21 2020. gxl g85d6ad1 - longyong.chen@droid02-sz Board ID = 8, adc=617 set vcck to 1070 mv set vddee to 1070 mv CPU clk: 1200MHz LPower: DDR3 chl: Rank0+1 @ 792MHz - FAIL DDR3 chl: Rank0 @ 792MHz bist_test rank: 0 29 00 52 3c 18 61 27 00 4f 43 20 66 26 00 4d 41 20 63 25 00 4a 40 21 60 601 - PASS Rank0: 1024MB(auto)-2T-11 ssc: ppm1000- AddrBus test pass! NAND init Load fip header from NAND, src: 0x0000c000, des: 0x01400000, size: 0x00004000 New fip structure! Load bl30 from NAND, src: 0x00010000, des: 0x013c0000, size: 0x00007600 Load bl301 from NAND, src: 0x00018000, des: 0x01380000, size: 0x00002600 Load bl31 from NAND, src: 0x0001c000, des: 0x10100000, size: 0x00019600 Load bl33 from NAND, src: 0x00038000, des: 0x01000000, size: 0x00081000 NOTICE: BL3-1: v1.0(debug):361f8a7 NOTICE: BL3-1: Built : 16:43:26, Dec 19 2018 NOTICE: BL31: GXL normal boot! NOTICE: BL31: BL33 decompress pass [Image: gxl_v1.1.3103-9234004 2018-12-27 10:43:23 yao.zhang@droid07] efuse init ops = e4 efuse init hdcp = c, cf9=7 x2_hp_e = 0 bl30: check_permit, count is 1 bl30: check_permit: ok! chipid: 0 0 3 c c 0 f0 b3 a8 a0 0 e4 not ES chip[0.599863 Inits done] INFO: BL3-1: Initializing runtime services WARNING: No OPTEE provided by BL2 boot loader ERROR: Error initializing runtime service opteed_fast INFO: BL3-1: Preparing for EL3 exit to normal world INFO: BL3-1: Next image address = 0x1000000 INFO: BL3-1: Next image spsr = 0x3c9 U-Boot 2015.01-gfdaaeeb-dirty (Nov 01 2021 - 15:04:09) DRAM: 1 GiB gxl_p211_1g [BL31]: tee size: 0 osd_size 720p bootmode:NORM gxl_p211_1g IH_COMP_LZOOK uboot time: 8434708 us [ 0.000000@0] Initializing cgroup subsys cpu [ 0.000000@0] Initializing cgroup subsys cpuacct [ 0.000000@0] CPU: ARMv71 Processor [410fd034] revision 4 [ 0.000000@0] no prop version_code [ 0.000000@0] bootconsole [earlycon0] enabled get_dvfs_info 0008 INFO: HDCP22 key read fail! INFO: p1d 0 INFO: pd1 0 [ 1[BL31]: tee size: 0 [BL31]: tee size: 0 [BL31]: tee size: 0 [BL31]: tee size: 0 WARNING: Unimplemented Sip Call: 0x82000036 root@p200_2G:/ # [ 16.138041@2] monitor: received netlink message:anstvbw new ok [ 16.138237@2] monitor:reply

› 綜合交流 / 資源分享區 › 綜合交流大區